HPE Aruba Networking Q9H62A AP-515 Indoor Access Points

• Hardware variants
  AP-515: Internal antenna models

  Wi-Fi radio specifications

  AP type: Indoor, dual radio, 5GHz 802.11ax 4×4 MIMO and 2.4GHz 802.11ax 2×2 MIMO 5GHz radio: Four spatial stream Single User (SU) MIMO for up to  4.8Gbps wireless data rate to individual 4SS HE160 802.11ax client devices (max) Two spatial stream Single User (SU) MIMO for up to  1.2Gbps wireless data rate to individual 2SS HE80 802.11ax client devices (typical) Four spatial stream Multi User (MU) MIMO for up to 4.8Gbps wireless data rate to up to four 1SS or two 2SS HE160 802.11ax DL-MU-MIMO capable client devices simultaneously (max) Four spatial stream Multi User (MU) MIMO for up to 2.4Gbps wireless data rate to up to four 1SS or two 2SS HE80 802.11ax DL-MU-MIMO capable client devices simultaneously (typical) 2.4GHz radio: Two spatial stream Single User (SU) MIMO for up to 574Mbps wireless data rate to individual 2SS HE40 802.11ax client devices or to two 1SS HE40 802.11ax DL-MU-MIMO capable client devices simultaneously (max) Two spatial stream Single User (SU) MIMO for up to 287Mbps wireless data rate to individual 2SS HE20 802.11ax client devices or to two 1SS HE20 802.11ax DL-MU-MIMO capable client devices simultaneously (typical) Support for up to 512 associated client devices per radio, and up to 16 BSSIDs per radio Supported frequency bands (country-specific restrictions apply): 2.400 to 2.4835GHz ISM 5.150 to 5.250GHz U-NII-1 5.250 to 5.350GHz U-NII-2A 5.470 to 5.725GHz U-NII-2C 5.725 to 5.850GHz U-NII-3/ISM 5.850 to 5.895GHz U-NII-4 Available channels: Dependent on configured regulatory domain Dynamic frequency selection (DFS) optimizes the use of available RF spectrum Including Zero-Wait DFS (ZWDFS) to accelerate channel changes Supported radio technologies: 802.11b: Direct-sequence spread-spectrum (DSSS) 802.11a/g/n/ac: Orthogonal frequency-division multiplexing (OFDM) 802.11ax: Orthogonal frequency-division multiple access (OFDMA) with up to 16 resource units (for an 80MHz channel) Supported modulation types: 802.11b: BPSK, QPSK, CCK 802.11a/g/n: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM (proprietary extension) 802.11ac: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM, 1024-QAM (proprietary extension) 802.11ax: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM, 1024-QAM 802.11n high-throughput (HT) support: HT20/40 802.11ac very high throughput (VHT) support: VHT20/40/80/160 802.11ax high efficiency (HE) support: HE20/40/80/160 Supported data rates (Mbps) 1: 802.11b: 1, 2, 5.5, 11 802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54 802.11n (2.4GHz): 6.5 to 300 (MCS0 to MCS15, HT20 to HT40) 802.11n (5GHz): 6.5 to 600 (MCS0 to MVC31, HT20 to HT40) 802.11ac: 6.5 to 3,467 (MCS0 to MCS9, NSS = 1 to 4, VHT20 to VHT160) 802.11ax (2.4GHz): 3.6 to 574 (MCS0 to MCS11, NSS = 1 to 2, HE20 to HE40) 802.11ax (5GHz): 3.6 to 4,803 (MCS0 to MCS11, NSS = 1 to 4, HE20 to HE160) 802.11n/ac packet aggregation: A-MPDU, A-MSDU Transmit power: Configurable in increments of 0.5 dBm Maximum (aggregate, conducted total) transmit power (limited by local regulatory requirements): 2.4 GHz band: +21 dBm (18dBm per chain) 5 GHz band: +24 dBm (18 dBm per chain) Note: conducted transmit power levels exclude antenna gain. For total (EIRP) transmit power, add antenna gain. Advanced Cellular Coexistence (ACC) minimizes the impact of interference from cellular networks Maximum ratio combining (MRC) for improved receiver performance Cyclic delay/shift diversity (CDD/CSD) for improved downlink RF performance Space-time block coding (STBC) for increased range and improved reception Low-density parity check (LDPC) for high-efficiency error correction and increased throughput Transmit beam-forming (TxBF) for increased signal reliability and range 802.11ax Target Wait Time (TWT) to support low-power client devices 802.11mc Fine Timing Measurement (FTM): for precision distance ranging   1 Ignoring the impact of proprietary data rate extensions and OFDMA resource units.

  Wi-Fi antennas

  AP-515: Four integrated dual-band downtilt omni-directional antennas for 4×4 MIMO with peak antenna gain of 4.2dBi in 2.4GHz and 7.5dBi in 5GHz. Built-in antennas are optimized for horizontal ceiling mounted orientation of the AP. The downtilt angle for maximum gain is roughly 30 degrees. Combining the patterns of each of the antennas of the MIMO radios, the peak gain of the effective per-antenna pattern is 3.8dBi in 2.4GHz and 4.6dBi in 5GHz.

  Additional interfaces

  E0: HPE SmartRate port (RJ-45, maximum negotiated speed 2.5Gbps) Auto-sensing link speed (100/1000/2500BASE-T) and MDI/MDX 2.5Gbps speed complies with NBase-T and 802.3bz specifications POE-PD: 48Vdc (nominal) 802.3af/802.3at POE E1: 10/100/1000BASE-T Ethernet network interface (RJ-45) Auto-sensing link speed and MDI/MDX Link aggregation (LACP) support between both network ports for redundancy and increased capacity DC power interface: 12Vdc (nominal, +/- 5%), accepts 2.1mm/5.5mm center-positive circular plug with 9.5mm length USB 2.0 host interface (Type A connector) Capable of sourcing up to 1A / 5W to an attached device Bluetooth 5 and Zigbee (802.15.4) radio Bluetooth: up to 8dBm transmit power (class 1) and -95dBm receive sensitivity Zigbee: up to 8dBm transmit power and -97dBm receive sensitivity Integrated vertically polarized omnidirectional antenna with roughly 30 degrees downtilt and peak gain of 3.5dBi (AP-515) or 4.9dBi (AP-514) Visual indictors (two multi-color LEDs): for System and Radio status Reset button: factory reset, LED mode control (normal/off) Serial console interface (proprietary, micro-B USB physical jack) Kensington security slot

• Power sources and power consumption

  The AP supports direct DC power and Power over Ethernet (POE; on port E0) When both power sources are available, DC power takes priority over POE Power sources are sold separately; see the ordering Information section below for details When powered by DC or 802.3at POE, the AP will operate without restrictions When powered by 802.3af POE and with the IPM feature enabled, the AP will start up in unrestricted mode, but it may apply restrictions depending on the PoE budget and actual power. What IPM restrictions to apply, and in what order, is programmable. Operating the AP with an 802.3af (class 3 or lower) PoE source and IPM disabled is not supported (except for AP staging; no radios will be enabled).​ Maximum (worst-case) power consumption: DC powered: 16W POE powered (802.3af, IPM enabled): 13.5W POE powered (802.3at/bt): 20.8W All numbers above are without an external USB device connected. When sourcing the full 5W power budget to such a device, the incremental (worst-case) power consumption for the AP is up to 5.7W (PoE powered) or 5.5W (DC powered). Maximum (worst-case) power consumption in idle mode: 12.6W (PoE) or 9.7W (DC) Maximum (worst-case) power consumption in deep-sleep mode: 5.9W (PoE) or 1.5W (DC)

  Mounting details
  A mounting bracket has been pre-installed on the back of the AP. This bracket is used to secure the AP to any of the (sold separately) mount kits; see the ordering Information section below for details.

  Mechanical
  Dimensions/weight (AP-515; unit, excluding mount bracket): (H) 46mm x (W) 200mm x (D) 200mm (1.8″ x 7.9″ x 7.9″) Weight: 810g (28.5oz) Dimensions/weight (AP-515; shipping): (H) 72mm x (W) 230mm x (D) 220mm (2.8″ x 9.1″ x 9.1″) Weight: 1,010g (35.5oz)

  Environmental
  Operating conditions Temperature: 0°C to +50°C / +32°F to +122°F Humidity: 5% to 93% non-condensing AP is plenum rated for use in air-handling spaces ETS 300 019 class 3.2 environments Storage and transportation conditions Temperature: -40°C to +70°C / -40F to +158°F Humidity: 5% to 93% non-condensing ETS 300 019 classes 1.2 and 2.3 environments

  Reliability
  Mean Time Between Failure (MTBF): 560,000 hrs (64yrs) at +25°C operating temperature.

  Regulatory compliance

  FCC/ISED CE Marked RED Directive 2014/53/EU EMC Directive 2014/30/EU Low Voltage Directive 2014/35/EU UL/IEC/EN 60950 EN 60601-1-1, EN60601-1-2 Railway Certs (AP-515 Only): EN 50155:2017 – Railway Applications EN 50121-1:2017 – Railway EMC EN 50121-3-2 – Railway EMC EN 50121-4:2016 – Railway Immunity IEC 61373 ed2:2008 – Railway Shock and Vibration For more country-specific regulatory information and approvals, please see your HPE Aruba Networking representative.

  Regulatory model numbers
  AP-515: APIN0515

  Certifications
  UL2043 plenum rating Wi-Fi Alliance: Wi-Fi CERTIFIED a, b, g, n, ac Wi-Fi CERTIFIED ax2 WPA, WPA2 and WPA3 – Enterprise, Personal WMM, WMM-PS, W-Fi Agile Multiband Passpoint (release 2) Wi-Fi location Bluetooth SIG Ethernet Alliance (POE, PD device, class 4)   2 May require software update. Certification effort will be kicked off as soon as the Wi-Fi Alliance starts the program.

  Minimum operating system software versions
  ArubaOS and Aruba InstantOS 8.4.0.0 ArubaOS 10.0.0.0

  Warranty
  Aruba’s hardware limited lifetime warranty

Download PDF